Furnace Faults Diagnosed Before Parts Are Ordered

Furnace Repair in Grafton for heating systems that won't ignite, cycle correctly, or produce adequate heat

Many older Central Massachusetts homes run furnaces well past their expected service life, and when those systems fail, the repair decision involves more than just the broken part—it involves an honest assessment of what the system has left. Air Temperature Service, LLC repairs furnaces in Grafton and nearby towns, diagnosing the specific fault before any parts are quoted. The company stocks common components on its trucks and has completed residential heating repairs across this area since 1981, with the owner in the trade since 1976.


The technician works through the ignition sequence, flame sensor, blower, limit switch, and safety controls in order, then reads the control board for stored fault codes before confirming the cause. Parts are identified and explained before work starts. Most common repairs are finished on the same visit, and if the repair no longer makes sense given the system's age and condition, Air Temperature Service, LLC will say so plainly rather than applying a patch that buys a single season.


To arrange a furnace diagnostic for your Grafton home, call (508) 466-7476 and describe what the system is doing—or not doing.

Why Furnace Problems Happen and How to Stop Them

Most furnace failures fall into a recognizable sequence: the ignition fires, the flame sensor does not confirm the burner, and the control board locks the system out after two or three failed attempts. That cycle can look identical whether the flame sensor is simply coated with oxidation—a five-minute fix—or whether the gas valve is failing to deliver adequate pressure, which is a more involved repair. The technician measures temperature rise across the heat exchanger as a standard step, because a cracked heat exchanger produces a specific temperature pattern that separates it from a simple airflow restriction before either diagnosis reaches the point of opening the unit.


After a completed repair, the furnace ignites reliably on the first call from the thermostat, the blower delivers consistent airflow through the duct system, and the carbon monoxide and venting checks confirm the system is safe to run. Homes in Shrewsbury and Westborough with older colonial floor plans sometimes have extended duct runs that create static pressure issues the new repair can surface—the technician notes those conditions separately so they can be addressed rather than attributed to the repair that was just completed.


The question of repair versus replacement comes up most often when the heat exchanger is involved, since a cracked exchanger cannot be patched and the cost of a new one approaches the cost of replacing the furnace entirely. Air Temperature Service, LLC provides that assessment as part of the diagnostic, not as an upsell after the repair has already started.

Common Questions About This Service

These questions cover how furnace repair work is carried out and what homeowners can expect during and after the service visit.

  • How does the technician determine whether the flame sensor is the problem?

    The technician measures microamp output at the sensor while the burner is firing—a reading below the manufacturer's specification confirms the sensor is failing to detect the flame reliably, even if the burner itself is burning normally.

  • What does measuring temperature rise across the heat exchanger reveal?

    The difference between supply and return air temperatures should fall within a specific range for the furnace model; a rise that is too high indicates restricted airflow, while an inconsistent reading across the heat exchanger can indicate a crack or breach in the exchanger itself.

  • Why does a furnace short-cycle even after the ignition problem is fixed?

    Short-cycling is often caused by the high-limit switch tripping due to restricted airflow from a dirty filter, blocked registers, or a failing blower motor—the technician checks airflow as a standard step regardless of the primary fault.

  • What happens during the carbon monoxide and venting check before the technician leaves?

    The technician confirms combustion gases are exiting through the flue, checks for backdrafting at the draft hood or pressure switch ports, and verifies no CO is present in the supply air before the system is returned to service.

  • How do you prepare the system for a repair visit?

    Clear access to the furnace cabinet, note the thermostat behavior and any error codes displayed on the control board, and locate the emergency shutoff switch—these details reduce diagnostic time on the first visit.

Air Temperature Service, LLC also repairs furnaces in Berlin, Milford, Framingham, Marlborough, and Shrewsbury. If your heating system has stopped working or is behaving inconsistently, call (508) 466-7476 to schedule a diagnostic visit with a technician who can give you a straight answer about what the repair involves.