Ductwork That Delivers Air Where It Belongs

Ductwork Installation and Repair in Grafton for leaking joints, undersized runs, and systems that heat or cool unevenly

Uneven room temperatures, rooms that never reach the thermostat setting, and heating or cooling equipment that runs longer than it should are often duct problems rather than equipment problems. Air Temperature Service, LLC installs and repairs residential ductwork in Grafton and nearby Central Massachusetts towns, addressing the distribution system alongside the furnace, air conditioner, or heat pump it serves. Treating the duct layout as a secondary concern when installing new equipment is a reliable way to underperform a correctly sized system from the first day it runs.


Every assessment begins with a check of the existing duct layout for leaks at joints and connections, disconnected sections, and runs that are undersized for the rooms they serve or the equipment they connect to. Leaking joints are sealed and insulated; undersized runs are corrected or replaced with new ductwork sized to the actual airflow requirements of the equipment and the space. Older ranch and colonial homes in Grafton—including those in areas like Auburn and Ashland where additions and alterations have been layered onto original duct systems over decades—frequently have a mix of original trunk lines and later-added branches that do not balance well without correction.


Arrange a ductwork assessment with Air Temperature Service to identify specific leaks, disconnections, or undersized runs affecting your system's air distribution.

What Proper Ductwork Repair and Installation Requires

Duct sealing is not accomplished with standard household tape, which fails at the joints between metal sections over time. Mastic sealant or purpose-made metal tape is applied to every joint and connection that shows evidence of leakage, and insulation is checked or added on runs that pass through unconditioned spaces such as attics or crawlspaces. New duct runs are sized using the airflow requirements of the equipment and the Manual D methodology, which accounts for run length, the number of fittings, and the heat load of the room being served.


After repairs are complete, rooms that previously failed to reach the thermostat setting during heating or cooling operation should begin performing consistently with the rest of the house. Supply registers that once delivered noticeably less air than others will show improved flow, and the heating or cooling equipment should cycle off at or near the set temperature rather than running continuously to compensate for conditioned air escaping through leaking joints.


When ductwork repair is performed alongside a new equipment installation, the sequence matters: duct corrections should be completed before the new system is commissioned so that the equipment is sized and charged against the actual, corrected duct system rather than a leaking or restricted one. Air Temperature Service handles ductwork as part of the same scope as the heating and cooling equipment it installs, rather than treating it as a separate trade.

Questions Before Starting Your Ductwork Project

The following questions address how ductwork repair and installation work is performed and what to expect when the job involves an existing duct system that has been modified over time.

  • How are duct leaks identified before repairs begin?

    The technician inspects joints, connections, and transitions throughout the accessible duct system, looking for gaps, separated sections, and evidence of air escape such as dust accumulation at joint edges or disconnected flex duct collars.

  • What materials are used to seal duct joints?

    Mastic sealant applied to metal-to-metal joints and UL 181-rated metal foil tape are the appropriate materials for a durable duct seal; standard duct tape deteriorates at the adhesive layer and is not a lasting repair for pressurized duct joints.

  • How does an added room or finished basement affect the existing duct system on older Grafton homes?

    An addition tapped into an existing trunk line without recalculating airflow often pulls conditioned air away from other rooms on the same run, creating the uneven temperatures that lead homeowners to assume the equipment is undersized when the real issue is distribution.

  • Why does insulating duct runs in unconditioned spaces matter for system performance?

    A duct run carrying conditioned air through an uninsulated attic loses a measurable portion of that air's temperature before it reaches the supply register, which reduces the effective capacity the system delivers to the room regardless of what the equipment is rated at.

  • How are new duct runs sized when they are added to an existing system?

    Sizing is determined by the airflow requirement of the room being served—its heat load and distance from the supply plenum—not by matching the diameter of an adjacent existing run, which may itself be undersized for its current load.

Air Temperature Service, LLC also installs and repairs ductwork in Berlin, Milford, Framingham, Marlborough, and Shrewsbury. To discuss the condition of your current duct layout or get an assessment before a new system installation, call (508) 466-7476.